







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterWhat Cabinet Refacing Costs in Garland, TX – and When It’s the Wrong Spend
Refacing kitchen cabinets in Garland typically costs $4,000-$9,000 for a 15-20 linear-foot ranch kitchen, while full cabinet replacement in the same space runs $12,000-$22,000 with KraftMaid or Wellborn boxes. That gap is real, and we’ll quote it to you in writing before any work begins. But there’s a catch most cost pages skip: refacing only pays off if the original box is structurally sound. Call (844) 560-4146 and we’ll tell you which side of that line your cabinets are on at the in-home visit.

Why Garland Kitchens Age Differently Than the Cost Guides Assume
Most of Garland’s housing stock went up between the 1950s and 1970s, and the tract subdivisions east and south of downtown carry original cabinets built the way builders built them then: particleboard boxes fastened with staples and a few nails, often with a thin vinyl or paper veneer over the surface. Then forty to sixty years of North Texas summers happened.
Here’s what the generic cost calculators never mention. Garland sits on Blackland Prairie clay that swells and shrinks through wet-dry cycles, and that foundation movement works on cabinet boxes the same way it works on door frames – joints open, seams work loose, fasteners wallow out. Add a Garland summer of 100-degree heat and heavy humidity, and a ranch kitchen with no exhaust ventilation becomes a slow steam bath every time someone boils pasta. That moisture migrates into particleboard, and particleboard doesn’t recover. It swells, delaminates, and crumbles around the fasteners holding it together. In drier climates a refacing job buys you fifteen good years on a 1970 box. Here, on an unventilated interior kitchen, we’ve seen the same box keep failing inside two.
That’s why we inspect the box before we quote doors. It’s also why our Kitchen Remodeling projects often start with a recommendation the homeowner didn’t expect – replacement instead of refacing – and we’d rather hand you that news for free than sell veneer over a failing carcass. A written price comes after that assessment, not before.
Test Your Own Cabinets Before You Spend a Dollar
You can run this check in about ten minutes with a flashlight and your hands. It won’t tell you everything a contractor will catch, but it’ll flag the three failure modes we see most often in original 1960s-70s Garland cabinets.
- The sink-floor press. Put your palm flat on the cabinet floor under the sink and push down, hard. A solid plywood box stays rigid. A soft spot means water has been reaching the particleboard for years. Any give at all is a red flag.
- The drawer-slide mount check. Open a few drawers and look at the screws holding the slides to the cabinet frame. Stripped holes, screws sitting loose, or slides that have been moved and remounted tell you the box material can’t hold a fastener anymore. If it can’t hold a drawer slide, it won’t reliably hold a refaced door for long.
- The corner delamination look. Shine your flashlight into the interior corners and along the top edges. Particleboard that has taken on moisture comes apart in visible layers – it looks like a dry pastry. Crumbling or lifting edges at the corners mean the structural material is already compromised.
If all three checks come back solid, you probably have plywood boxes worth refacing. If two or more show problems, replacement is likely the smarter spend, and no veneer job changes that.

What Refacing Actually Covers – and What Drives the Number
Refacing replaces the doors and drawer fronts, applies a matching veneer to the visible face frames and side panels, and installs new hardware and slides. The box itself stays. That’s what makes it roughly half the cost of replacement, faster to complete, and gentler on a kitchen that’s still in daily use.
Where refacing makes economic sense: solid plywood boxes that pass the three-point test, doors that are tired but frames that are square, and a firm budget. Where we’ll steer you to replacement: failed particleboard boxes, cabinets that need reconfiguration (a wall opened up, an island added), or boxes that are out of square from foundation movement.
For Garland homes, here’s how refacing compares against the alternative in the same kitchen:
| Item | Typical Range |
|---|---|
| Refacing, 15-20 linear feet (doors, veneer, hardware) | $4,000-$9,000 |
| Full cabinet replacement with KraftMaid or Wellborn boxes | $12,000-$22,000 |
| Small kitchen remodel (full scope, at the lower end) | $9,000-$20,000 |
| Standard kitchen remodel, Garland | $14,000-$45,000 |
| Cabinet installation only | $4,000-$13,000 |
| Countertop installation (quartz or solid surface) | $2,000-$6,500 |
What pushes the refacing number toward $9,000: more than 20 linear feet, glass or custom panel doors, new soft-close undermount slides throughout, and a countertop swap done at the same time. What keeps it near $4,000: a tight U-shaped ranch kitchen, standard door styles, and keeping the existing counters. If you’re already planning to reface and replace counters together, Cambria, Silestone, and Caesarstone are the lines we source, and pairing the two jobs saves the labor of two separate visits.
The 365-Day Done Right Promise and the Box Limit
Every refacing project comes with a written price before work starts and our 365-Day Done Right Promise: if the veneer lifts, the new slides fail, or the finish doesn’t hold inside that year, we come back and fix it at no charge. If the repair fails again, the return visit costs you nothing – no service call, no re-inspection fee. That part of the promise is straightforward and we’ll put it in writing.
What we won’t do is pretend the promise covers the original box. If a cabinet carcass fails eighteen months after refacing because it was already delaminating when we got there, that’s the box failing, not our work – and it’s exactly why the box inspection happens before we issue the written price. We’d rather have that honest conversation at your kitchen table than after demo day. It’s the same discipline behind every Penhallow Remodeling Garland project: say the price before the work, show up in the arrival window, and leave the kitchen cleaner than we found it. A live person answers our phone around the clock, and our technicians are background-checked and arrive in uniform.
Downstream of the refacing, the rest of a Garland kitchen sometimes needs attention too – original cast-iron drain lines under older homes, countertops that have been waiting their turn. Those are conversations for the estimate, not surprises mid-job. If the scope grows into a real remodel, the ranges hold steady: $14,000-$45,000 for the full scope, and we’ll walk the whole thing before anyone touches a cabinet.
FAQs
Cabinet refacing in Garland typically runs $4,000-$9,000 for a standard 15-20 linear-foot ranch kitchen, with doors, veneer, and new hardware included. The number climbs toward $9,000 for larger kitchens, custom door styles, or new slides throughout. Call (844) 560-4146 for an exact written quote – the in-home visit is free and the box inspection comes with it.
Yes, refacing usually costs about half of full replacement – $4,000-$9,000 against $12,000-$22,000 for new KraftMaid or Wellborn boxes in the same kitchen. It’s only cheaper in the long run if the original boxes pass a structural check. If the box is delaminating or can’t hold a fastener, you’ll pay twice. Call us and we’ll assess the box before you commit a dollar.
Press the cabinet floor under the sink for soft spots, check the screw holes where drawer slides mount for stripped or loose fasteners, and look into the interior corners for visible layer separation. Two or more failures point to replacement, not refacing. In Garland’s older ranch kitchens, decades of humidity often push original particleboard past the point of saving. Call (844) 560-4146 and we’ll confirm in person.
A typical Garland refacing job takes two to four days from demo of the old doors to the finished install, depending on kitchen size and door style. That’s a real advantage over replacement, which can run two to three weeks with countertop and plumbing work added. We confirm the timeline in writing before work starts. Call for a free estimate.
Get a Written Price Before Anyone Touches a Cabinet
If your kitchen boxes are sound, refacing is one of the smartest spends in the house. If they’re not, we’ll tell you at the visit, not after the deposit. Either way, you get a written price and a written guarantee before work starts. Call (844) 560-4146 for a free estimate in Garland – a real person answers, 24/7.
Written by the team at Penhallow Remodeling Garland, serving Garland, TX.
What Our Customers Say
"Full home refresh before we sold. They were straight about what was worth doing and what wasn't to get our money back. On time, on budget, and it sold in a week."
- Monica Vaughn"Did our whole kitchen. The written estimate held, which after reading remodel nightmares online I did not take for granted. Showed up every morning on time and the crew was clean and polite."
- Warren Updike"Kitchen and dining room opened up into one space. They were honest about which wall could come down and which couldn't, no sugarcoating. Dust was kept way down with plastic everywhere."
- Oscar Benitez












